Magneum Associates

• Emergency water-stopping capability 
• Single component - only the addition of clean water is required
• Excellent bond to the substrate
• Low exotherm minimises thermal cracking
• Pre-bagged formulation to overcome variations in site batching
• Contains no chloride admixtures

• Single component - Easy to use
• Versatile - Can be used for plaster, masonry or concrete,can
• be painted after application
• Non sagging - Can be used for horizontal, vertical and overhead applications
• Good adhesion - Eff ective bonding with substrate
• Non Shrink - Shrinkage cracking eliminated

• Advanced Technology : New generation molecule yields high performance concrete. Suitable for any grade of concrete including higher grades.
• Corrosion resistant: Meets the requirements of Japanese code JIS Z1535 (modifi ed) fi rst of kinds in the integral water proofi ng range.
• High Strength : Due to better dispersion of cement particles and helps in the better degree of hydration yielding high strength compared to control.
• Cohesive Mix : Improves workablity and cohesiveness of the concrete.
• Durablity : Improves durability due to reduction in permeability of concrete and corrosion resistance of steel.

• Add cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1 minutes.
• Start addition of 75–80% mixing water & mix for 2-3 minutes.
• Fosroc Conplast WL Xtra is added as per the recom-  mended dosage into the remaining mixing / gauging  water, then add to concrete mixer & mix for another 2 minutes.
• Place the concrete or apply plaster, as needed.
• Cure the applied mortar or concrete as per good construction practices or use Fosroc Concure curing compounds

• Do not add Fosroc Conplast WL Xtra directly to dry cement & aggregate mix.
• Maintain water-cement ratio as low as possible.
• Do not increase the dosage of Conplast WL Xtra than the recommendation.  

Product Details:
The product is designed to be easily mixed on site using a slow speed drill fitted with a mixing paddle and then applied to the substrate using brush, roller, trowel or spray. The finished coating is of a slightly granular texture.
Brushbond RFX is a two component acrylic polymer modifi ed cementitious coating which consists of Brushbond RFX powder and Brushbond RFX liquid acrylic emulsion. It requires only the addition of clean water at site to produce an easily brushable coating. Brushbond RFX can simply be applied by stiff brush, roller or trowel to obtain the desired thickness.

Uses:
Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments.
The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications

Advantages:

Ex celle nt b arrie r to carbo n dioxide, chloride and sulphate ions.

Allows water vapour to escape from the structure.

Waterproof-suitable for water retaining structures.

High resistance to the effect of long-term weathering, durable in all climate conditions including UV attack.

Non toxic - ideal for potable water tanks.

Flexible, with thermal expansion similar to concrete.

Excellent bond to concrete and masonry.

Good crack accommodation capacity.

Minimum surface preparation needed and low labour costs.

Application:
For best results, surfaces should be damp. In order to obtain the protective properties of Brushbond RFX, it is important that the correct rates of application are observed. Use a short stiff brush preferably 120-150mm width and apply the mixed material like paint.
The application of Brushbond RFX should not be done if the temperature of the substrate is below 100C. When applying Brushbond RFX on hot substrates i.e., over 300C surface temperature, saturate the surface with water. Apply Brushbond RFX in 2 coats to achieve 1mm thickness. The second coat of Brushbond RFX shall be applied as soon as the fi rst coat has reached touch dry state. It is recommended that for general surfacing Brushbond RFX should be applied at a minimum thickness of 1mm. Areas subjected to moderate and heavy loads/hydrostatic pressure, minimum 2mm thickness coating is recommended with screed above. Water curing OR Curing membrane shall not be applied over Brushbond RFX coating, only air curing is recommended

Application Instructions:
Surface Preparation 
All surfaces which are to receive the coating must be free from oil, laitance, grease, wax, dirt or any other form of foreign matter which might affect adhesion. Typically concrete surfaces can be cleaned using high pressure water jet or grit blasting or by proper wire brushing Spalled surfaces or those containing large blow holes, cracks and other such defects should be repaired using Renderoc concrete repair mortars. For further advice on suitable repair mortars, contact the local Fosroc Office.

High performance two component elastomeric cementitious damp-proof coating. Uses Nitoproof Damp Protect is a High performance two component elastomeric cementitious damp-proof coating, suitable for application on concrete, brick wall and plastered surface both positive & negative side. Areas of Application Masonry surface,concrete, plaster surface  and  brick            walls subjected to damage from moisture / effl  orescence.  Toilets and wet areas. Balconies, chajjas and utilities. Advantages Suitable for treatment of damp patches from negative side Excellent crack bridging ability. Excellent adhesion to concrete, masonry and plastered    surface. Long working life. Easy application by brush, roller, trowel or spray. Bonds to green or damp surface. Eff ective barrier to sulphates, chlorides & carbonation. Provides long lasting protection against effl  orescence.

Product Details:
The product is designed to be easily mixed on site using a slow speed drill fitted with a mixing paddle and then applied to the substrate using brush, roller, trowel or spray. The finished coating is of a slightly granular texture.
Brushbond RFX is a two component acrylic polymer modifi ed cementitious coating which consists of Brushbond RFX powder and Brushbond RFX liquid acrylic emulsion. It requires only the addition of clean water at site to produce an easily brushable coating. Brushbond RFX can simply be applied by stiff brush, roller or trowel to obtain the desired thickness.
Uses:
Brushbond RFX is an high performance elastomeric cementitious coating used for waterproofi ng and to protect atmospherically exposed reinforced concrete structures from attack by acid gases, chloride ions, oxygen & water. Brushbond RFX is suitable for all types of structures including those in coastal environments.
The product can be used on concrete, brick and blockwork substrates and is equally suitable for new and existing structures. The product is designed to reface and even out variations in concrete and masonry surfaces and bridge shrinkage cracks. It provides a seamless, fl exible waterproof coating suitable for water tanks, reservoirs, drainage culverts basements, roofs, toilets & wet areas. The product provides a tough durable water resistant coating which can withstand light pedestrian traffi c and also has excellent weather resistance for exterior applications
Advantages:
Ex celle nt b arrie r to carbo n dioxide, chloride and sulphate ions.
Allows water vapour to escape from the structure.
Waterproof-suitable for water retaining structures.
High resistance to the effect of long-term weathering, durable in all climate conditions including UV attack.
Non toxic - ideal for potable water tanks.
Flexible, with thermal expansion similar to concrete.
Excellent bond to concrete and masonry.
Good crack accommodation capacity.
Minimum surface preparation needed and low labour costs.
Application:
For best results, surfaces should be damp. In order to obtain the protective properties of Brushbond RFX, it is important that the correct rates of application are observed. Use a short stiff brush preferably 120-150mm width and apply the mixed material like paint.
The application of Brushbond RFX should not be done if the temperature of the substrate is below 100C. When applying Brushbond RFX on hot substrates i.e., over 300C surface temperature, saturate the surface with water. Apply Brushbond RFX in 2 coats to achieve 1mm thickness. The second coat of Brushbond RFX shall be applied as soon as the fi rst coat has reached touch dry state. It is recommended that for general surfacing Brushbond RFX should be applied at a minimum thickness of 1mm. Areas subjected to moderate and heavy loads/hydrostatic pressure, minimum 2mm thickness coating is recommended with screed above. Water curing OR Curing membrane shall not be applied over Brushbond RFX coating, only air curing is recommended
Application Instructions:
Surface Preparation
All surfaces which are to receive the coating must be free from oil, laitance, grease, wax, dirt or any other form of foreign matter which might affect adhesion. Typically concrete surfaces can be cleaned using high pressure water jet or grit blasting or by proper wire brushing Spalled surfaces or those containing large blow holes, cracks and other such defects should be repaired using Renderoc concrete repair mortars. For further advice on suitable repair mortars, contact the local Fosroc Office.

Lokfix E45T is Fosroc’s solution for medium duty anchoring into cracked and un-cracked concrete and post installation of reinforcement. Also used in stone and masonry. Comes with industry leading accreditation and design software.

For concrete (solid, porous and light), masonry and hollow bricks.

Accredited* for use in dry, wet and flooded concrete substrates, internal and external exposure.
Can be used with cracked concrete
Fixing of post installed reinforcement and tension anchors
Anchoring of threaded rod fixings
Can be applied to a wide variety of fixing and rebar sizes
For horizontal, vertical and overhead application
Bonding and surface crack sealing applications prior to Nitofill injection.
Advantages
High bond strength
Extended open time for working in high temperatures or on complex setting configurations.
Can use with a good quality skeleton gun (300ml size), No additional mixing equipment required
Does not apply expansive force to the substrate
Enables fixings closer to edges than mechanical anchors
Low VOC
Re-usable by replacing sealing cap  product may be kept to the end of original shelf life.
Waterproof, protecting the embedded fixing from corrosion and water penetration into the substrate.
C1  and C2 seismic resistance*

For large repairs, the mixed Renderoc RG may be modified by the site addition of 8 mm to 12 mm clean graded, saturated, surface dry aggregates

Lokfix E45T is Fosroc's solution for medium duty anchoring into cracked and un-cracked concrete and post installation of reinforcement. Also used in stone and masonry. Comes with industry leading accreditation and design software. For concrete (solid, porous and light), masonry and hollow bricks.

DESCRIPTION Sika® Injection-101 h is a low viscous, fast foaming and solvent-free water-reactive polyurethane injection, which cures to form a dense flexible foam with a fine cellular structure.                                                                                                             USES Sika® Injection-101 h is used for the temporary water stopping of high water intrusions in cracks, joints and cavities in concrete, brickwork and natural stonework. 

• Polyurethane (PU) Hybrid, long-life waterproofing coating system
• 15-year waterproofing warranty
• Acrylate with flutyne technology
• 1 mm film thickness
• Tough durable elastic membrane with > 300% elongation
• Surface temperature reduction upto 10ºC
• Highly foot trafficable coating